- Do I need a coax cable for WiFi?
- Does CB coax length matter?
- How many ohms is rg59?
- Is BNC analog or digital?
- Which is better 50 ohm or 75 ohm?
- What is 50 ohm coax used for?
- How do you match a 75 ohm to a 50 ohm?
- How can you tell the difference between 50 Ohm and 75 Ohm BNC?
- What is a 75 ohm antenna?
- Can I use 50 ohm coax for TV?
- What do you mean by coaxial?
- Does coax length affect SWR?
- Can I use 75 ohm coax for CB?
- Is rg6 a 75 ohm?
- Can you use TV coax for CB?
- Can I use 75 ohm cable instead 50?
- What is 75 ohm coaxial cable used for?
- What is a coaxial cable used for?
Do I need a coax cable for WiFi?
A coax cable is required to connect your modem/gateway to the Comcast network.
Your WiFi devices may also receive other WiFi signals from other gateways/routers which you might be able to connect to without your own modem/gateway/router, in which case, no coax cable is required..
Does CB coax length matter?
CB coax cable is necessary to connect your antenna to your radio. The coaxial cable running from your radio to the antenna is VERY important. Everything you transmit and receive must travel along it’s length. All too often, the coax is ignored and performance suffers because of the lack of attention it receives.
How many ohms is rg59?
75 ohmsRG-59/U is a specific type of coaxial cable, often used for low-power video and RF signal connections. The cable has a characteristic impedance of 75 ohms, and a capacitance of around 20pF/ft (60pF/m). The 75 ohm impedance matches a dipole antenna in free space.
Is BNC analog or digital?
Both 50 ohm and 75 ohm versions are available. The BNC connector is used for signal connections such as: analog and serial digital interface video signals.
Which is better 50 ohm or 75 ohm?
Especially when it comes to 50 Ohm vs 75 Ohm coax cables. In short, cables are measured by impedance, how much resistance there is to the flow of electrical energy. The smaller the Ohm, the better the performance. So a 50 Ohm cable provides much better results than a 75 Ohm cable.
What is 50 ohm coax used for?
So 50 ohm cables are intended to be used to carry power and voltage, like the output of a transmitter. If you have a small signal, like video, or receive antenna signals, the graph above shows that the lowest loss or attenuation is 75 ohms.
How do you match a 75 ohm to a 50 ohm?
So you have an approx 75 ohm impedance antenna and you want to get the best match you can. Take the wavelength of the frequency, multiply it by the velocity factor of your 75 ohm matching coax and multiply again by 0.0815. For example.
How can you tell the difference between 50 Ohm and 75 Ohm BNC?
Basically, 50-ohm BNC connectors are used for older analog video applications. But for higher performance A/V applications like HDTVs, 75-ohm BNC devices are necessary. 75-ohm BNC connectors can, however, be used for analog purposes.
What is a 75 ohm antenna?
There isn’t really such a thing as a “75 ohm antenna.” What happens is actually a bit sneakier. Modern antennas use a device called a balun that serves two purposes. … The result is that the 300 ohm impedance is reduced to 75 or 50 ohms which is a much more compatible result for copper coaxial cable.
Can I use 50 ohm coax for TV?
A good rule of thumb is that any device that functions as a transmitter or transceiver tends to use 50 Ohm Coaxial Cable. This includes devices such as CB/Ham Radios, Broadcast Radio/TV Transmitters, Wi-Fi and Cellular Phone Repeaters and 2-Way Radios (Walkie Talkies). … Our next most popular is RG-174 Coaxial Cable.
What do you mean by coaxial?
In geometry, coaxial means that two or more three-dimensional linear forms share a common axis. Thus, it is concentric in three-dimensional, linear forms. A coaxial cable, as a common example, is a three-dimensional linear structure.
Does coax length affect SWR?
“the length of the feedline will not change the swr it will change the apparent reading depending on what wave length you read the swr at. . just as adding a signifigant length of coax, the resultant loss will look like a lower swr.”
Can I use 75 ohm coax for CB?
RG-59 and RG-6 are 75 Ohm coaxial cables designed for cable television applications, they tend to have wide frequency response and low line loss. … You can use these cables with a 50 Ohm amateur radio antenna system, but because of the impedance mismatch, your SWR will be a little higher.
Is rg6 a 75 ohm?
An RG-6/U coaxial cable has a characteristic impedance of 75 ohms. The term, RG-6, is generic and is applied to a wide variety of cable designs, which differ from one another in shielding characteristics, center conductor composition, dielectric type and jacket type.
Can you use TV coax for CB?
Does this mean that you cannot use Cable TV coax? Not at all. Assuming you have a modern-day rig, its output network is designed to accommodate a 50-Ω load, but the network can usually handle a 75 Ω impedance with little difficulty (you may see an SWR of approximately 1.5:1).
Can I use 75 ohm cable instead 50?
3 Answers. Sure, you can use 75 ohm coax instead of 50 ohm. In some cases (such as feeding a dipole), 75 ohm coax may be a better match to the load than 50 ohm. … A 75 ohm load on a transmitter designed for a 50 ohm load is only a 1.5:1 SWR, which isn’t that bad.
What is 75 ohm coaxial cable used for?
75-Ohm coaxial cable is primarily used for audio and video. This is the reason why it is used so widely throughout our homes and business premises.
What is a coaxial cable used for?
Coaxial cable is used as a transmission line for radio frequency signals. Its applications include feedlines connecting radio transmitters and receivers to their antennas, computer network (e.g., Ethernet) connections, digital audio (S/PDIF), and distribution of cable television signals.